Skip to main content
LaserRoomReady
Menu
Check my space

Workbench planning · xTool P2S

xTool P2S Workbench Size: Footprint, Depth and Weight

The published P2S body is 39.37 × 25.16 in and weighs 99.2 lb. A supporting surface must accommodate that closed body before any rear connections, lid travel, material path or service allowance is added. A 24-inch-deep top is 1.16 inches shallower than the published machine depth.

  • Official xTool sources
  • Original calculations
  • Reviewed 2026-09-09
  • No hands-on performance claim
01 · Published facts

Start with the documented envelope.

Published body

39.37 × 25.16 × 10.55 in

1000 × 639 × 268 mm

Body footprint

6.88 ft²

Calculated from the published width and depth

Published weight

99.2 lb

45 kg; accessories and materials are additional

24-inch bench

1.16 in too shallow

Body comparison only; foot placement is not published

02 · Original calculation

What the published envelope says about common bench sizes

  • A 48 × 30 in top leaves 8.63 in across the machine width and 4.84 in along the depth before operating allowances.
  • A 40 × 30 in top leaves only 0.63 in across—an intentionally tight result even though the closed body is arithmetically smaller.
  • A 24-inch-deep top is 29.4 mm / 1.16 in shallower than the published body. LaserRoomReady does not infer that overhang is permitted.
  • The calculated body footprint is 0.639 m² / 6.88 ft². This is not a recommended table size.
Calculated does not mean manufacturer-approved.

Arithmetic can expose a conflict or tight margin. It cannot establish support suitability, delivery handling, operating clearance, ventilation, electrical capacity, fire protection or code compliance.

03 · Use it in the room

Turn the comparison into a measured plan.

  1. Measure the usable top after lips, uprights, walls, and fixed items are excluded.
  2. Confirm the support's documented load rating and stability for the complete operating configuration.
  3. Obtain xTool's current requirements for lid travel, rear service, hoses, cables, and material travel.
  4. Enter the measured surface and complete room into the full checker before ordering.
Room first

Compare every supported profile

Enter one surface and room zone, then order candidates by evidence and fit rather than price.

Full report

Check the featured model

Carry the model into delivery, surface, room, exhaust and utility checks.

Complete handoff

Laser-room setup checklist

Carry the calculation into delivery, operating space, air path, utilities, materials, and confirmations.

Total cost

xTool setup-cost builder

Record machine, air-management, attachment, support, site, shipping, tax, and material costs.

Launch alternative

X1 vs P2S vs P3 tracker

Separate published X1 facts from purchase and room details that remain unknown.

Purchase research

xTool buying options

Compare official listings after the room and configuration questions are visible.

04 · Open evidence

Keep these questions unresolved until confirmed.

  • The cited sources do not publish one numeric minimum workbench size.
  • The locations of the machine's support feet are not substituted for the full published envelope.
  • Numeric open-lid and service clearances remain unresolved.
This page is not a product review.

LaserRoomReady has not physically tested the featured machines. It compares cited room-planning evidence and original calculations only.

05 · Questions people ask

Direct answers, with the boundary intact.

Can a P2S sit on a 24-inch-deep workbench?

The published body is 25.16 inches deep, so its envelope exceeds a 24-inch top by 1.16 inches. LaserRoomReady does not treat unsupported overhang as acceptable.

Is a 40-inch-wide bench enough?

The closed body is 39.37 inches wide, leaving only 0.63 inches total. That is a tight geometry result before side access, controls or material handling.

06 · Evidence

Manufacturer sources used on this page

01
xTool P2S product pageChecked 2026-09-09
02
xTool P2S FAQChecked 2026-09-09
03
xTool P2S user guideChecked 2026-09-09
07 · Current configurations

Continue only after the room questions are visible.

These merchant links are clearly labeled. LaserRoomReady may earn a commission at no extra cost to you if you buy through one. Compensation does not change the calculations or display order.

Related planning pages