Skip to main content
LaserRoomReady
Menu
Check my space

Common-bench comparison · 24-inch depth

Which xTool Fits a 24-Inch-Deep Workbench?

At the closed-body level, S1 and M2 are shallower than 24 inches; P2S is not. S1 leaves 1.91 inches and M2 leaves 1.60 inches, while P2S exceeds the top by 1.16 inches. Width, capacity, stability, connections, and operating clearance still determine whether a location works.

  • Official xTool sources
  • Original calculations
  • Reviewed 2026-09-09
  • No hands-on performance claim
01 · Published facts

Start with the documented envelope.

P2S depth

25.16 in

Exceeds 24 in by 1.16 in

S1 depth

22.09 in

Leaves 1.91 in before allowances

M2 depth

22.40 in

Leaves 1.60 in before allowances

Meaning

Body screen only

Not a workbench recommendation or approval

02 · Original calculation

The same depth does not mean the same usable setup

  • 24.00 − 25.16 = −1.16 in for the P2S published body.
  • 24.00 − 22.09 = 1.91 in for S1 without its riser.
  • 24.00 − 22.40 = 1.60 in for the M2 basic body.
  • P2S, S1, and M2 widths are 39.37, 30.12, and 24.02 in, respectively; a surface still needs adequate usable width.
Calculated does not mean manufacturer-approved.

Arithmetic can expose a conflict or tight margin. It cannot establish support suitability, delivery handling, operating clearance, ventilation, electrical capacity, fire protection or code compliance.

03 · Use it in the room

Turn the comparison into a measured plan.

  1. Measure the real top depth at its shallowest usable point.
  2. Enter usable width and documented load rating in the reverse finder.
  3. Add rear connections, exhaust components, lid access, and material travel from current documentation.
  4. Treat the result as a shortlist, then run the full checker for the selected model.
Room first

Compare every supported profile

Enter one surface and room zone, then order candidates by evidence and fit rather than price.

Full report

Check the featured model

Carry the model into delivery, surface, room, exhaust and utility checks.

Complete handoff

Laser-room setup checklist

Carry the calculation into delivery, operating space, air path, utilities, materials, and confirmations.

Total cost

xTool setup-cost builder

Record machine, air-management, attachment, support, site, shipping, tax, and material costs.

Launch alternative

X1 vs P2S vs P3 tracker

Separate published X1 facts from purchase and room details that remain unknown.

Purchase research

xTool buying options

Compare official listings after the room and configuration questions are visible.

04 · Open evidence

Keep these questions unresolved until confirmed.

  • This comparison does not account for foot locations or authorize overhang.
  • Furniture nominal dimensions may exceed the actual usable top.
  • No general numeric operating allowance is assumed for any model.
This page is not a product review.

LaserRoomReady has not physically tested the featured machines. It compares cited room-planning evidence and original calculations only.

05 · Questions people ask

Direct answers, with the boundary intact.

Does S1 or M2 automatically work on a 24-inch bench?

No. Their closed bodies are shallower, but the complete operating configuration and supporting surface still need confirmation.

Can I rotate a machine on the bench?

Only if controls, loading, exhaust, service, and the room arrangement make that practical. The finder asks rather than silently rotating it.

06 · Evidence

Manufacturer sources used on this page

01
xTool P2S product pageChecked 2026-09-09
02
xTool P2S user guideChecked 2026-09-09
03
xTool S1 user guideChecked 2026-09-09
04
xTool M2 FAQChecked 2026-09-09
05
xTool M2 user guideChecked 2026-09-09
07 · Current configurations

Continue only after the room questions are visible.

These merchant links are clearly labeled. LaserRoomReady may earn a commission at no extra cost to you if you buy through one. Compensation does not change the calculations or display order.

Related planning pages