Skip to main content
LaserRoomReady
Menu
Check my space

Complete setup planner · xTool P2S

xTool P2S Setup Requirements: Table, Power, Exhaust, and Accessories

The published P2S body is 39.37 × 25.16 × 10.55 inches and weighs 99.2 pounds. xTool lists 100–120 VAC and a 700 W maximum for the U.S. machine. Those values cover neither the supporting surface nor accessory loads. Plan the laser, exhaust or filtration equipment, optional riser or conveyor, delivery package, connections, and access as separate items.

  • Official xTool sources
  • Original calculations
  • Reviewed 2026-09-10
  • No hands-on performance claim
01 · Published facts

Start with the documented envelope.

Closed machine body

39.37 × 25.16 × 10.55 in

1000 × 639 × 268 mm

Published machine weight

99.2 lb / 45 kg

Before accessories, workpieces, and support equipment

Published U.S. input

100–120 VAC; 700 W maximum

Verify the exact region, nameplate, and frequency

Exhaust choices

Outdoor route or compatible filtration

IF2 2.0 and AP2 paths are documented by xTool

02 · Original calculation

Treat the setup as a system rather than one machine rectangle

  • The closed body occupies about 6.88 ft² before allowances for hoses, cables, lid travel, rear service, or material travel.
  • A 24-inch-deep top is 1.16 inches shallower than the published machine body.
  • A 48 × 30 in top leaves 8.63 inches across the body width and 4.84 inches in depth before operating allowances.
  • The published 700 W maximum is a machine figure, not a complete laser-room or branch-circuit calculation.
Calculated does not mean manufacturer-approved.

Arithmetic can expose a conflict or tight margin. It cannot establish support suitability, delivery handling, operating clearance, ventilation, electrical capacity, fire protection or code compliance.

03 · Use it in the room

Turn the comparison into a measured plan.

  1. Measure the usable supporting surface and obtain its documented load rating and stability requirements.
  2. Select the exact base, riser, rotary, conveyor, exhaust, or filtration configuration before drawing the operating envelope.
  3. Inventory each machine and accessory nameplate separately for review by the manufacturer or a licensed electrician.
  4. Obtain order-specific package dimensions and walk the full delivery route before shipment.
Room first

Compare every supported profile

Enter one surface and room zone, then order candidates by evidence and fit rather than price.

Full report

Check the featured model

Carry the model into delivery, surface, room, exhaust and utility checks.

Complete handoff

Laser-room setup checklist

Carry the calculation into delivery, operating space, air path, utilities, materials, and confirmations.

Total cost

xTool setup-cost builder

Record machine, air-management, attachment, support, site, shipping, tax, and material costs.

Launch alternative

X1 vs P2S vs P3 tracker

Separate published X1 facts from purchase and room details that remain unknown.

Purchase research

xTool buying options

Compare official listings after the room and configuration questions are visible.

04 · Open evidence

Keep these questions unresolved until confirmed.

  • General order-specific P2S carton dimensions and weight remain unresolved in the main profile.
  • The cited sources do not publish one numeric minimum table size or complete open-lid and service envelope.
  • This page does not size a circuit, fan, duct, filter, make-up-air path, or fire-protection system.
This page is not a product review.

LaserRoomReady has not physically tested the featured machines. It compares cited room-planning evidence and original calculations only.

05 · Questions people ask

Direct answers, with the boundary intact.

Does the P2S require a 700 W circuit?

No circuit conclusion follows from that number alone. It is xTool's published machine maximum; accessory loads, nameplates, continuous use, and applicable electrical requirements remain separate.

Should I use an inline fan or AP2?

They represent different documented paths. Choose the route that matches the exact machine, materials, and location, then confirm every connection and requirement.

Can the P2S body sit on a 24-inch-deep workbench?

Its published depth is 25.16 inches, so the closed body exceeds a 24-inch top before any connections or clearances are added.

06 · Evidence

Manufacturer sources used on this page

01
xTool P2S product pageChecked 2026-09-09
02
xTool P2S FAQChecked 2026-09-09
03
xTool P2S user guideChecked 2026-09-09
04
xTool exhaust-accessory compatibility guideChecked 2026-09-10
05
xTool SafetyPro IF2 2.0 FAQChecked 2026-09-10
06
xTool SafetyPro AP2 FAQChecked 2026-09-10
07 · Current configurations

Continue only after the room questions are visible.

These merchant links are clearly labeled. LaserRoomReady may earn a commission at no extra cost to you if you buy through one. Compensation does not change the calculations or display order.

Related planning pages